IPS 2007 pint

SUBSTRATE RECOMMENDATIONS  
WELD-ON 2007 is formulated for rigid vinyl, and foamed PVC to themselves and to each other.

BONDING RECOMMENDATIONS  
WELD-ON 2007 is recommended where a water-thin cement is desired. It is suitable and used on both large  assemblies and small delicate assemblies. These include a wide variety of items: signs, large displays, lighting  fixtures, housewares, electrical assemblies, decorator items and many other fabrications.

GENERAL DESCRIPTION  
WELD-ON 2007 is a clear, water-thin, fast drying solvent. It may be applied by brush, syringe, spray, and most  any other method. It forms bonds by the softening and fusion of the two surfaces in contact. Bonds made with  WELD-ON 2007 cure rapidly. Cure is effected by dissipation of the solvent. Initial bond takes place within a few  minutes and is often of sufficient strength to permit handling of the bonded item. Relatively high strength is  reached in 24 to 48 hours and continues to increase for a number of weeks. Joined materials will generally have  the same rigidity or flexibility and other physical properties as prior to bonding.

ADHESIVE PROPERTIES AND CHARACTERISTICS

COLOR: Clear
VISCOSITY: Water-Thin
WORKING TIME: 1 – 2 minutes
FIXTURE TIME: 3 minutes
80% STRENGTH: 24 – 48 hours
SPECIFIC GRAVITY: .85 ± .040
COVERAGE: Unknown, no way to determine


DIRECTIONS FOR USE  
• JOINT PREPARATION: Parts to be joined should fit without forcing. Surfaces should be clean and smooth.  A good machine finish or sanding with 200-400 grit sandpaper should be satisfactory. Surfaces “as molded  or extruded” may not require additional preparation.  
• APPLICATION OF CEMENT: WELD-ON 2007 can be applied by brush, spray, pump type oil cans, syringe,  eye dropper, saturated felt pad and other devices. Cement may be applied to one or both surfaces.  
• ASSEMBLY OF PARTS: Assemble while parts are still wet. If cement is applied to one surface, let the two  surfaces be in gentle contact for a few seconds to allow the cement to soften the dry surface. Then press  parts together in firm contact. If both the parts have been coated, they may be brought firmly together  immediately. The application of pressure of 2 to 10 pounds per square inch should materially increase  bond strength. Spring loaded clothespins may be suitable as clamps. The length of time required for clamp  or jig pressure will vary. A few hours may be required for difficult joints and a few minutes for parts that fit  well and have modest load requirements.

SHELF LIFE  Three years expectancy in tightly sealed containers. Stability of the product is limited by the permanence of the  container and the evaporation of the solvent when container is open.

SHIPPING  Shipping Information for Individual Containers Larger than One Liter: DOT Shipping Name: Flammable  Liquid, n.o.s. (Methyl Ethyl Ketone, Tetrahydrofuran). DOT Hazard Class: 3. ID #: UN1993. Packaging Group: II.  Label: Flammable Liquid.

Shipping Information for Less than One Liter: DOT Shipping Name: Consumer Commodity. DOT Shipping  Class: ORM-D.

SAFETY AND ENVIRONMENTAL PRECAUTIONS  
Weld-On 2007 is a flammable, fast evaporating, solvent cement. It is considered a hazardous material. In  conformance with the Federal Hazardous Substances Labeling Act, the following hazards and precautions are  given. Purchasers who may re-package this product must also conform to all local, state and federal labeling,  safety and other regulations.

DANGER! – EXTREMELY FLAMMABLE – VAPOR HARMFUL –  MAY BE HARMFUL IF SWALLOWED – MAY IRRITATE SKIN OR EYES  
Keep out of reach of children. Do not take internally. Keep away from heat, spark, open flame and other sources  of ignition. Keep container closed when not in use. Store in the shade below 80ºF. Use only with adequate  ventilation. Avoid breathing of vapors. Atmospheric levels should be maintained below established exposure limit  values contained in Section II and VIII of the Material Safety Data Sheet. If airborne concentrations exceed those  limits, use of a NIOSH-approved organic vapor cartridge respirator with full face-piece is recommended. The  effectiveness of an air-purifying respirator is limited. Use it only for a single short-term exposure. For emergency  and other conditions where short-term exposure guidelines may be exceeded, use an approved positive pressure  self-contained breathing apparatus. Do not smoke, eat or drink while working with this product. Avoid contact with  skin, eyes and clothing. May cause eye injury. Protective equipment such as gloves, safety goggles and  impervious apron should be used. Carefully read Material Safety Data Sheets and follow all precautions. Contains  Tetrahydrofuran (109-99-9) and Methyl Ethyl Ketone (78-93-3). Do not use this product for other than intended  use.  "Title Ill Section 313 Supplier Notification": This product contains toxic chemicals subject to the reporting  requirements of Section 313 of the Emergency Planning and Community Right-to-Know Act of 1986 and of  40CFR372. This information must be included in all MSDS’s that are copied and distributed for this material.

FIRST AID  Inhalation: If ill effects from inhalation, remove to fresh air. If not breathing, give artificial respiration. If breathing is  difficult, give oxygen. Call physician.

Eye or Skin Contact: Flush with plenty of water for 15 minutes. If irritation persists, get medical attention.  Ingestion: If swallowed, do not induce vomiting. Contact physician immediately.

QUALITY ASSURANCE  Every batch of this cement is checked to assure that consistent quality is maintained. An infrared absorption curve  is recorded for each batch to ensure that this cement is properly formulated. Samples are taken from all batches  and kept for a period of at least one year. A batch identification code is stamped on each can.

IMPORTANT NOTE  This product is intended for use by skilled individuals at their own risk. These suggestions and data are based on  information we believe to be reliable. Users should verify by test that this product, as well as these methods, are  suited to their application. Since specific use, materials and handling are not controlled by IPS, our warranty is  limited to the replacement of defective IPS products.

If you need more information on this product please click the following link to view the manufacturer's literature page.