IPS 2354 pint
SKU: IPS2354-PT
Item Weight: 1 lb
Sales Unit: EA
Details
SUBSTRATE RECOMMENDATIONS
WELD-ON 2354 is formulated for bonding ABS, styrene (general purpose high impact), acrylics and poly-carbonates to themselves. It should not be used for joining dissimilar materials such as: ABS to styrene, ABS to acrylics, ABS to PVC or PVC to styrene.
BONDING RECOMMENDATIONS
WELD-ON 2354 is recommended for joining ABS, styrene and acrylics to themselves where a water-thin cement is desired. It is suitable and used on both large assemblies and small delicate assemblies. These include a wide variety of items: signs, large displays, lighting fixtures, housewares, electrical assemblies, decorator items and many other fabrications.
GENERAL DESCRIPTION
WELD-ON is a clear, water-thin, fast drying solvent cement. It may be applied by brush, syringe, spray, and most any other method. It forms bonds by the softening and fusion of the two surfaces in contact. Cure is affected by dissipation of the solvent and cures rapidly. Initial bonds take place within a few minutes and is often of sufficient strength to permit handling of the bonded item. Relatively high strength is reached in 24 to 48 hours, and continues to increase for a number of weeks. The joined material will generally have the same rigidity or flexibility and other physical properties as prior to bonding.
ADHESIVE PROPERTIES AND CHARACTERISTICS
COLOR: Clear
VISCOSITY: Water-Thin
WORKING TIME: 3 minutes
FIXTURE TIME: 5 minutes
80% STRENGTH: 72 hours
SPECIFIC GRAVITY: .81 ± .040
COVERAGE: Unknown, no way to determine
DIRECTIONS FOR USE
• JOINT PREPARATION: Parts to be joined should fit without forcing. Surfaces should be clean and smooth. A good machine finish or sanding with 200-400 grit sandpaper should be satisfactory. Surfaces “as molded or extruded” may not require additional preparation.
• ASSEMBLY OF PARTS: Assemble while parts are still wet. If cement is applied to one surface, let the two surfaces be in gentle contact for a few seconds to allow the cement to soften the dry surface. Then press parts together in firm contact. If both of the parts have been coated, they may be brought firmly together immediately. The application of pressure of 2 to 10 pounds per square inch should materially increase bond strength. Spring-loaded clothespins may be very suitable as clamps. The length of time required for clamp or jig pressure will vary. A few hours may be required for difficult joints and a few minutes for parts that fit well and have modest load requirements.
• CAPILLARY METHOD: Parts are placed lightly together and cement is applied to the edge of the joint with brush, eyedropper, or syringe. By capillary action, the cement will flow a considerable distance between two such surfaces. After a few seconds are allowed for the cement to soften the surfaces, the parts may be pressed together firmly. Where surfaces are very smooth and fit well together, it is sometimes possible to obtain good joints without additional clamping pressure. However, it may be best in most cases to maintain clamp pressure as outlined above.
• APPLICATION OF CEMENT: WELD-ON 2354 can be applied by brush, spray, pump type oil cans, syringe, eye dropper, saturated felt pad and other devices.
SHELF LIFE Three years expectancy in tightly sealed containers. Stability of the product is limited by the permanence of the container and the evaporation of the solvent when container is open.
SHIPPING
Shipping Information for Individual Containers Larger than One Liter: DOT Shipping Name: Methyl Ethyl Ketone. DOT Hazard Class: 3. ID #: UN1193. Packaging Group: II. Label: Flammable Liquid.
Shipping Information for Less than One Liter: DOT Shipping Name: Consumer Commodity. DOT Shipping Class: ORM-D.
SAFETY AND ENVIRONMENTAL PRECAUTIONS
Weld-On 2354 is a flammable, fast evaporating, solvent cement. It is considered a hazardous material. In conformance with the Federal Hazardous Substances Labeling Act, the following hazards and precautions are given. Purchasers who may re-package this product must also conform to all local, state and federal labeling, safety and other regulations.
CAUTION! – FLAMMABLE – VAPOR HARMFUL – MAY BE HARMFUL IF SWALLOWED – MAY IRRITATE SKIN OR EYES
Keep out of reach of children. Do not take internally. Keep away from heat, spark, open flame and other sources of ignition. Keep container closed when not in use. Store in the shade below 80ºF. Use only with adequate ventilation. Avoid breathing of vapors. Atmospheric levels should be maintained below established exposure limit values contained in Section II and VIII of the Material Safety Data Sheet. If airborne concentrations exceed those limits, use of a NIOSH-approved organic vapor cartridge respirator with full face-piece is recommended. The effectiveness of an air-purifying respirator is limited. Use it only for a single short-term exposure. For emergency and other conditions where short-term exposure guidelines may be exceeded, use an approved positive pressure self-contained breathing apparatus. Do not smoke, eat or drink while working with this product. Avoid contact with skin, eyes and clothing. May cause eye injury. Protective equipment such as gloves, safety goggles and impervious apron should be used. Carefully read Material Safety Data Sheets and follow all precautions. Contains Methyl Ethyl Ketone (78-93-3). Do not use this product for other than intended use. "Title III Section 313 Supplier Notification": This product contains toxic chemicals subject to the reporting requirements of Section 313 of the Emergency Planning and Community Right-to-Know Act of 1986 and of 40CFR372. This information must be included in all MSDS’s that are copied and distributed for this material.
FIRST AID Inhalation: If ill effects from inhalation, remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Call physician.
Eye or Skin Contact: Flush with plenty of water for 15 minutes. If irritation persists, get medical attention. Ingestion: If swallowed, do not induce vomiting. Contact physician immediately.
QUALITY ASSURANCE
Every batch of this cement is checked to assure that consistent quality is maintained. An infrared absorption curve is recorded for each batch to ensure that this cement is properly formulated. Samples are taken from all batches and kept for a period of at least one year. A batch identification code is stamped on each can.
IMPORTANT NOTE
This product is intended for use by skilled individuals at their own risk. These suggestions and data are based on information we believe to be reliable. Users should verify by test that this product, as well as these methods, are suited to their application. Since specific use, materials and handling are not controlled by IPS, our warranty is limited to the replacement of defective IPS products.
If you need more information on this product please click the following link to view the manufacturer's literature page.
WELD-ON 2354 is formulated for bonding ABS, styrene (general purpose high impact), acrylics and poly-carbonates to themselves. It should not be used for joining dissimilar materials such as: ABS to styrene, ABS to acrylics, ABS to PVC or PVC to styrene.
BONDING RECOMMENDATIONS
WELD-ON 2354 is recommended for joining ABS, styrene and acrylics to themselves where a water-thin cement is desired. It is suitable and used on both large assemblies and small delicate assemblies. These include a wide variety of items: signs, large displays, lighting fixtures, housewares, electrical assemblies, decorator items and many other fabrications.
GENERAL DESCRIPTION
WELD-ON is a clear, water-thin, fast drying solvent cement. It may be applied by brush, syringe, spray, and most any other method. It forms bonds by the softening and fusion of the two surfaces in contact. Cure is affected by dissipation of the solvent and cures rapidly. Initial bonds take place within a few minutes and is often of sufficient strength to permit handling of the bonded item. Relatively high strength is reached in 24 to 48 hours, and continues to increase for a number of weeks. The joined material will generally have the same rigidity or flexibility and other physical properties as prior to bonding.
| SUBSTRATE MATERIAL | 2 Hours | 24 Hours | 1 Week |
| ABS | 500 PSI | 1000 PSI | 1230 PSI |
| Polycarbonate | 1000 | 1800 | 2200 |
| Styrene | 500 | 1300 | 1800 |
ADHESIVE PROPERTIES AND CHARACTERISTICS
COLOR: Clear
VISCOSITY: Water-Thin
WORKING TIME: 3 minutes
FIXTURE TIME: 5 minutes
80% STRENGTH: 72 hours
SPECIFIC GRAVITY: .81 ± .040
COVERAGE: Unknown, no way to determine
DIRECTIONS FOR USE
• JOINT PREPARATION: Parts to be joined should fit without forcing. Surfaces should be clean and smooth. A good machine finish or sanding with 200-400 grit sandpaper should be satisfactory. Surfaces “as molded or extruded” may not require additional preparation.
• ASSEMBLY OF PARTS: Assemble while parts are still wet. If cement is applied to one surface, let the two surfaces be in gentle contact for a few seconds to allow the cement to soften the dry surface. Then press parts together in firm contact. If both of the parts have been coated, they may be brought firmly together immediately. The application of pressure of 2 to 10 pounds per square inch should materially increase bond strength. Spring-loaded clothespins may be very suitable as clamps. The length of time required for clamp or jig pressure will vary. A few hours may be required for difficult joints and a few minutes for parts that fit well and have modest load requirements.
• CAPILLARY METHOD: Parts are placed lightly together and cement is applied to the edge of the joint with brush, eyedropper, or syringe. By capillary action, the cement will flow a considerable distance between two such surfaces. After a few seconds are allowed for the cement to soften the surfaces, the parts may be pressed together firmly. Where surfaces are very smooth and fit well together, it is sometimes possible to obtain good joints without additional clamping pressure. However, it may be best in most cases to maintain clamp pressure as outlined above.
• APPLICATION OF CEMENT: WELD-ON 2354 can be applied by brush, spray, pump type oil cans, syringe, eye dropper, saturated felt pad and other devices.
SHELF LIFE Three years expectancy in tightly sealed containers. Stability of the product is limited by the permanence of the container and the evaporation of the solvent when container is open.
SHIPPING
Shipping Information for Individual Containers Larger than One Liter: DOT Shipping Name: Methyl Ethyl Ketone. DOT Hazard Class: 3. ID #: UN1193. Packaging Group: II. Label: Flammable Liquid.
Shipping Information for Less than One Liter: DOT Shipping Name: Consumer Commodity. DOT Shipping Class: ORM-D.
SAFETY AND ENVIRONMENTAL PRECAUTIONS
Weld-On 2354 is a flammable, fast evaporating, solvent cement. It is considered a hazardous material. In conformance with the Federal Hazardous Substances Labeling Act, the following hazards and precautions are given. Purchasers who may re-package this product must also conform to all local, state and federal labeling, safety and other regulations.
CAUTION! – FLAMMABLE – VAPOR HARMFUL – MAY BE HARMFUL IF SWALLOWED – MAY IRRITATE SKIN OR EYES
Keep out of reach of children. Do not take internally. Keep away from heat, spark, open flame and other sources of ignition. Keep container closed when not in use. Store in the shade below 80ºF. Use only with adequate ventilation. Avoid breathing of vapors. Atmospheric levels should be maintained below established exposure limit values contained in Section II and VIII of the Material Safety Data Sheet. If airborne concentrations exceed those limits, use of a NIOSH-approved organic vapor cartridge respirator with full face-piece is recommended. The effectiveness of an air-purifying respirator is limited. Use it only for a single short-term exposure. For emergency and other conditions where short-term exposure guidelines may be exceeded, use an approved positive pressure self-contained breathing apparatus. Do not smoke, eat or drink while working with this product. Avoid contact with skin, eyes and clothing. May cause eye injury. Protective equipment such as gloves, safety goggles and impervious apron should be used. Carefully read Material Safety Data Sheets and follow all precautions. Contains Methyl Ethyl Ketone (78-93-3). Do not use this product for other than intended use. "Title III Section 313 Supplier Notification": This product contains toxic chemicals subject to the reporting requirements of Section 313 of the Emergency Planning and Community Right-to-Know Act of 1986 and of 40CFR372. This information must be included in all MSDS’s that are copied and distributed for this material.
FIRST AID Inhalation: If ill effects from inhalation, remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Call physician.
Eye or Skin Contact: Flush with plenty of water for 15 minutes. If irritation persists, get medical attention. Ingestion: If swallowed, do not induce vomiting. Contact physician immediately.
QUALITY ASSURANCE
Every batch of this cement is checked to assure that consistent quality is maintained. An infrared absorption curve is recorded for each batch to ensure that this cement is properly formulated. Samples are taken from all batches and kept for a period of at least one year. A batch identification code is stamped on each can.
IMPORTANT NOTE
This product is intended for use by skilled individuals at their own risk. These suggestions and data are based on information we believe to be reliable. Users should verify by test that this product, as well as these methods, are suited to their application. Since specific use, materials and handling are not controlled by IPS, our warranty is limited to the replacement of defective IPS products.
If you need more information on this product please click the following link to view the manufacturer's literature page.