SUBSTRATE RECOMMENDATIONS
A wide variety of plastics and non-plastics to themselves and to each other; such as flexible and rigid vinyls,
acrylics, urethane foam and others to wood, metal, glass, masonry, canvas, rubber and other non-plastics.
BONDING RECOMMENDATIONS
WELD-ON 1829 is a medium bodied, water-resistant, modified elastomer and light tan in color. It is a part solvent
cement which cures with the dissipation of solvent to a very tough flexible film. It forms strong joints with rigid
materials, but affords high impact resistance because of its flexibility. It is highly resistant to water, oil and
gasoline. A thin film exposed to air will dry in 3 to 7 minutes.
USES
WELD-ON 1829 is being used in marine applications for bonding plasticized vinyls to masonry and metal and
patching vinyl sheets. It is also used in upholstering vinyl seats, bonding vinyl to urethane foam, canvas, as well
as other materials and attaching plastic letters to many substrates.
OTHER USES: Bonding aluminum or vinyl extrusions to concrete, repair of sporting equipment, leather goods,
shoes, saddles, belts and handbags.
ADHESIVE PROPERTIES AND CHARACTERISTICS
COLOR: Tan
VISCOSITY: 1500 cps
SPECIFIC GRAVITY: . 86 ± .040
COVERAGE: 10mil: 26 sq. ft/Pint 210 sq. ft/Gallon
20mil: 13 sq. ft/Pint 105 sq. ft/Gallon
DIRECTION FOR USE
• Clean surfaces to be joined.
• Coat each mating surface (2 coats if porous). Allow about 2 to 5 minutes for each to dry before assembly.
Film should be slightly tacky but not enough to transfer to the fingers using a light touch. Heavy coating may
require slightly longer to dry.
• Press parts firmly together. Use clamps or weights until cement has set sufficiently for handling strength. If
parts are strained, do not remove clamps for at least a few hours, depending on materials and room
temperature.
• Initial bond is suitable for handling. For good strength, allow 16 to 24 hours and bond strength will continue
to increase for a number of weeks.
• When applying cement to one piece, bring other piece in contact immediately and maintain contact for a few
hours before removing clamps or weights.
SHELF LIFE
Two years expectancy in tightly sealed containers. Stability of the product is limited by the permanence of the
container and the evaporation of the solvent when the container is open. Evaporation of solvent will cause the
cement to thicken and reduce the effectiveness of the cement.
SHIPPING
Shipping Information for Gallon and Above: DOT Shipping Name: Adhesive. DOT Hazard Class: 3. ID #:
UN1133. Packaging Group: II. Label: Flammable Liquid.
Shipping Information for Less than One Gallon: DOT Shipping Name: Consumer Commodity. DOT Shipping
Class: ORM-D.
SHIPPING
Shipping Information for Individual Container Larger than One Liter: DOT Shipping Name: Adhesive. DOT
Hazard Class: 3. ID #: UN1133. Packaging Group: II. Label: Flammable Liquid.
Shipping Information for Less than One Liter: DOT Shipping Name: Consumer Commodity. DOT Shipping
Class: ORM-D.
SAFETY AND ENVIRONMENTAL PRECAUTIONS
This product is a flammable, fast evaporating, solvent cement. It is considered a hazardous material. In
conformance with the Federal Hazardous Substances Labeling Act, the following hazards and precautions are
given. Purchasers who may re-package this product must also conform to all local, state and federal labeling,
safety and other regulations.
CAUTION! – FLAMMABLE – VAPOR HARMFUL –
MAY BE HARMFUL IF SWALLOWED – MAY IRRITATE SKIN OR EYES
Keep out of reach of children. Do not take internally. Keep away from heat, spark, open flame and other sources
of ignition. Keep container closed when not in use. Store in the shade between 40ºF and 110ºF. Use only with
adequate ventilation. Avoid breathing of vapors. Atmospheric levels should be maintained below established
exposure limit values contained in Section II and VIII of the Material Safety Data Sheet. If airborne concentrations
exceed those limits, use of a NIOSH-approved organic vapor cartridge respirator with full face-piece is
recommended. The effectiveness of an air-purifying respirator is limited. Use it only for a single short-term
exposure. For emergency and other conditions where short-term exposure guidelines may be exceeded, use an
approved positive pressure self-contained breathing apparatus. Do not smoke, eat or drink while working with this
product. Avoid contact with skin, eyes and clothing. May cause eye injury. Protective equipment such as gloves,
safety goggles and impervious apron should be used. Carefully read Material Safety Data Sheets and follow all
precautions. Contains Methyl Ethyl Ketone (78-93-3). Do not use this product for other than intended use.
"Title Ill Section 313 Supplier Notification": This product contains toxic chemicals subject to the reporting
requirements of Section 313 of the Emergency Planning and Community Right-to-Know Act of 1986 and of
40CFR372. This information must be included in all MSDS’s that are copied and distributed for this material.
FIRST AID
Inhalation: If ill effects from inhalation, remove to fresh air. If not breathing, give artificial respiration. If breathing
is difficult, give oxygen. Call physician.
Eye or Skin Contact: Flush with plenty of water for 15 minutes. If irritation persists, get medical attention.
Ingestion: If swallowed, do not induce vomiting. Contact physician immediately.
QUALITY ASSURANCE
Every batch of this cement is checked to assure that consistent quality is maintained. An infrared absorption curve
is recorded for each batch to ensure that this cement is properly formulated. Samples are taken from all batches
and kept for a period of at least one year. A batch identification code is stamped on each can.
IMPORTANT NOTE
This product is intended for use by skilled individuals at their own risk. These suggestions and data are based on
information we believe to be reliable. Users should verify by test that this product, as well as these methods, are
suited to their application. Since specific use, materials and handling are not controlled by IPS, our warranty is
limited to the replacement of defective IPS products.
If you need more information on this product please click the following link to view the manufacturer's literature page.
IPS Industrial Adhesives
